LSL MANTIS-RS PRO for Ducati Panigale V4 /S /R 18- / Panigale V2 20- / Streetfighter V4 20-

LSL MANTIS-RS PRO for Ducati Panigale V4 /S /R 18- / Panigale V2 20- / Streetfighter V4 20-

SKU: P.W._280-164LP
GTIN: 4054783622580
Category: Seitliche Kennzeichenhalter
Manufacturers:

Adjustable license plate holder for Ducati Panigale V4 /S /R 18- / Panigale V2 20- / Streetfighter V4 20-, incl. license plate light (E-approved)

117,95 €

incl. 19% VAT , plus (DPD)

Available immediately
Delivery time: 2 - 5 Workdays (DE - int. shipments may differ)

Description
Question about item

LSL MANTIS-RS license plate holder PRO with license plate light

Making good bikes perfect. Following this motto, LSL has developed the license plate holder MANTIS-RS PRO.

It fits perfectly to your motorcycle and emphasizes the lines of your bike with its sporty design.

And as usual from LSL, one has thought of everything.
The model-specific bracket of the MANTIS-RS PRO allows replacement without further drilling or cutting on the vehicle.
The design fits perfectly to the rear of your motorcycle, using the original mounting points of the vehicle.
Against damage to the cables, sharp-edged feedthroughs are protected with rubber membrane grommets.

The license plate is made of 2 mm thick sheet steel, laser-cut, edged and weather-resistant black powder coated.
The fixation of the license plate in the correct position is done by an additional locking screw.

The, adjustable in width, turn signal brackets of the MANTIS-RS PRO are suitable for any type of accessory turn signals. This adjustment option allows you to find the right position for your turn signals. The adaptation of the accessory turn signals to the most diverse EU license plates is therefore no problem. The mounting holes of the turn signals have a diameter of 8 mm and are slotted to the side. This allows the installation of the turn signals without disconnection from the wiring harness.

Also the slider for mounting the reflector is adjustable to your license plate size. Adaptation to the different designs of EU license plates is therefore no problem.

The two supplied rubber washers serve the vibration-reducing screw connection of the license plate. An additional rubber buffer supports the license plate on the underside.

In this PRO version of the MANTIS-RS is the very small, milled from high quality aluminum LSL license plate light with mounting plate and support arm included. The bracket is adjustable in height and designed to allow mounting in the position required by law.

Details:
- model-specific bracket
- infinitely adjustable turn signal holder
- slotted turn signal holder for easy mounting without cable separation
- infinitely adjustable reflector, E-approved
- suitable for European license plates
- infinitely adjustable tilt angle
- additional screw for optimum position security
- easy fixation without further work steps (eg.e.g. drilling)
- easy mounting of the license plate through slotted holes
- license plate light incl. Holder included
- license plate light, E-tested
- infinitely adjustable license plate light
- many different options for mounting the license plate light

Included with the MANTIS-RS PRO are:
- Model-specific bracket with mounting parts
- MANTIS-RS license plate holder plate
- Adjustable turn signal holders
- E-tested reflector with adjustable holder
- E-tested license plate light
- Mounting instructions

Note:
- For the original turn signals is optionally available in the accessories tab a special turn signal holder.
- If side reflectors are mounted on your original license plate holder, these must be reattached in a suitable position or replaced with new ones.

Tip:
If you have not found a model-specific license plate holder for your vehicle, the universal license plate holders from LSL, which are available in many different designs, are certainly a good alternative.

Contact data

E-Mail

Question about item

Your question